This

This blog will teach you how to Repurpose furniture like a Pro! There is nothing more rewarding than turning a dumpster find into an elegant showpiece.

When I pulled up to the dumpster and saw this abandoned old table I immediately knew I had to have it. The biggest challenge was getting it into my SUV.

Once I got it to my studio I started investigating it and found many things that needed repair.

The first thing I noticed was the leg was broken, this is usually not a problem except this leg had dowels holding it together rather than nails, in fact, the entire table was made by tongue and groove. This tells me that the table is very old.

Which brings me to another problem. If this table was made before 1978 it was probably painted with lead paint. UGH! This can be a health hazard and very dangerous to remove.

NO Worries, I’ll show you how to do it the safe way.

Read on for your step-by-step tutorial. The CHALLENGE is on!

Step #1 Repairs

The very first thing I had to do is fix the leg so I could stand it up and work on it.  I used a small saw to cut the dowels off so it would fit flush on the table.

It was missing a big chunk of wood so I had to do a little rebuilding. I used a Minwax wood filler (2 part epoxy).

I also had to use a piece of plastic to keep the wood filler from going all over the place.

Here’s a great video on how to repair wood.

This is what I did. I bought everything I needed at Home Depot.

MINWAX Wood FILLER

MIX AS DIRECTED 

I screwed on a temporary bracket to hold it in place. Then used the wood filler to repair the damage. Let dry over night.

When it was dry I removed the bracket and filled in the holes with wood filler and shaved off the excess. Then I used a 320 grit sand paper to smooth it out.

The bottom of the leg also needed repair.

So I made a brace out of plastic and sprayed it with WD40. Filled it in with wood filler and let it harden overnight.

Once it was hard I used the wood shaver to shape it like the other legs. Then used sandpaper to smooth it out.

Step #2 removing the paint

Just by looking at how the paint was flaking, I could tell that it was led paint. So I knew I had to take percussions.  Make sure you wear long sleeves, long pants, heavy-duty gloves, a mask and eye goggles.

Here’s a very informative tutorial on how to remove lead paint.

I started out spraying the paint with water and removed all the loose paint first.

Then used the paint remover and scraped off the paint. I had to go over it a couple of times to get through the layers. This stripping gel had a Citrus smell to it. It makes it a little more pleasant to work with.

I let it dry overnight and sanded it with a 320 grit sandpaper to get a smooth finish.

TIP: Always sand in the direction of the grain.

Clean the entire piece with a damp cloth or a tack cloth.

TIP: DON”T sand the area if it’s still wet. The paint remover will get all gummy and it will make it harder to sand.

This is the hardest part of the job but once it’s done you will feel a great sense of accomplishment. 

Now for the fun stuff!

Step #3 Staining

I used Minwax (Dark Walnut) stain. This is an oil-based product and it does have a little bit of an odor.   You’re going to need a paintbrush, rags, gloves to apply the stain.

Brush the stain in the direction of the grain then wipe off with the rag. The more layers you put on the darker the wood will get. I only used one coat of stain.

Let it dry overnight.

Once it dries apply a clear coat on top with a paintbrush. I used a Minwax Polyurethane fast-drying clear coat also bought at Home Depot. Let the first coat dry about 8 hours then apply a second coat.

Step #4 Chalk Paint

I love chalk paint. There is NO PREP  and is easy to use. Normally you don’t have to sand and prep when using chalk paint but in this case, I had to remove the lead paint. I used two different colors on this project. You don’t have to but I wanted to have a couple of colors come through when I distress it.

A quick TIP on distressing. DON’T overdo it. Less is more. Distress the areas that would normally be worn, like the edges and corner. You can do some in the middle of the piece but not too much, You want it to look authentic.

Apply the chalk paint with a paintbrush that won’t leave brush marks, these are the best brushes I have ever used. Let it dry for about 20 minutes and apply the second coat. Let it dry another 20 minutes and distress the edges and corners with fine or medium sandpaper.

I make my own chalk paint, it saves me a ton of money and it’s really easy. Buy any flat or matte paint and add this magic powder to it. Mix 2 TBSP Magic Powder to 2 TBSP water, then add to 1 cup paint., That’s it. This is the same adhesive used in the chalk paint you buy in the stores but for 1/4 of the price.

Learn: How to make your own chalk type paint!

Here’s another TIP: Some chalk paint companies recommend using their wax to seal it, but I found that many of them will change the color slightly.

Not to mention it’s a lot of rubbing. I used Rust-oleum Matte Clear Protective Top Coat. It doesn’t change the color and protects the finish. You can find it at Home Depot.

Step #5 Transferring Image

There are many ways to transfer an image and all of them have their own purpose. I have found this technique to be the fastest and easiest. The first thing you need to do is find an image for your project.

My go-to place is the Graphic Fairy

She has thousands of images to choose from.

After you down load your image print it out on regular copy paper. TIP: you don’t have to print it in the reverse just print it out.

Lay the transfer paper on your project then lay the image on top of that. Tape the edges in place so it doesn’t move.

Using a Precise V7 fine pen, start tracing the image on your furniture piece. You can buy the pens at Office Depot.

When you’re done remove the paper and fix any touch ups you might have.

If you want to peek to see if you’re using enough pressure just lift the paper gently and take a look.

Once you’re done with the transfer, seal it with Ben Moore “Stay Clear” This will keep it from smudging. This is my go to clear coat. Love this stuff!

Step #5 Apply Wallpaper to Draws

I like to add wallpaper inside the drawers and on the sides if the drawers have a flat surface. You can use wallpaper, wrapping paper or sheets of paper to add a little extra décor to your project.

If you want to save a bunch of money, find a designer or decorator that will give you her old wallpaper books. There tons of great patterns to work with.

If you have to buy the paper use wrapping paper or wallpaper. You can buy it in just about any store.

The easiest way to do this is…. Lay a piece of paper in the draw and use your finger and rub it along the edge to make a cress.

Cut it with a pair of scissors. Make sure it fits nicely before you glue it down.

Use an old credit card to rub out the air bubbles working it outward and wipe off excess glue.

TIP: Speaking of glue, I see so many people hooked on Mod Podge for their craft projects.

Let me let you in on a little secret. In my option, it’s just overpriced GLUE. I use whatever I had on hand. For this project, I used wallpaper paste. YUP! It’s Glue right? Its stick to walls, why wouldn’t stick to my draws.

So there you have it. And YES! It worked.

Once it’s dry brush on  stay clear for extra protection.

Add your hardware and you’re done.

If you want to learn how to start making money with your hobby get the details HERE

If you want to learn DIY Tricks and Tips get my weekly blog HERE